Orbit-attitude-vibration coupled dynamics of tethered solar power satellite

A new orbit-attitude-vibration coupled dynamic model of the tethered solar power satellite (Tethered SPS) is established based on absolute nodal coordinate formulation. The Hamilton’s equation of the system is derived by introducing generalized momentum through Legendre transformation. The correctness of the proposed model is verified by an example. The dynamic characteristics of the Tethered SPS are studied using the symplectic Runge-Kutta method. Simulation results show that the orbital radius and the total energy of the system are well preserved. The attitude of the system is unstable when the mass of the bus system is small. However, the attitude stability is dependent on some other parameters of the system, which requires further studies. It is also found that the average tether force/deformation can be roughly estimated by simplifying the solar panel as a particle. The proposed model can be used to study the orbit-attitude-vibration coupled dynamics and control problems.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种地月转移轨道中途修正的制导算法

针对地月转移轨道中途修正问题，提出了一种求解修正速度增量的制导算法。该算法由初值设计和精确解求解两部分组成。首先，利用伪状态理论，通过简单迭代设计中途修正的初值，并通过Vinti预报方法修正了地球扁率的影响。然后，在求解精确解时，提出了一种基于伪状态理论的状态转移矩阵解析算法。该算法通过设计高精度的初值，降低了求解地月转移轨道中途修正问题的难度，而且避免了传统数值方法计算状态转移矩阵的复杂性。数值仿真结果表明，该算法可有效求解中途修正问题。     

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

离心压缩机密封及空腔流动的一维/三维耦合建模研究

为了在保证数值预测精度的同时降低离心压缩机的建模复杂度,以一维密封泄漏计算替代完整的密封及空腔建模,开展了离心压缩机盖盘密封及空腔流动的源项建模方法研究。结果表明:基于源项方法的密封及空腔简化建模仅需在主流道建模基础上施加泄漏质量流量、总温和摩擦损失源项边界条件,即可较高精度地还原完整的盖盘密封及空腔建模的性能和关键流动细节。与完整建模相比,在全工况下源项建模预测的等熵效率的绝对偏差小于0.65%,总压比和等熵效率的相对性能偏差小于1%。该方法可在满足下游部件匹配设计精度需求的同时,减少50%以上的网格数量,并显著提高计算的经济性和收敛性。泄漏流量的计算精确度是影响源项建模法性能预测准确性的最关键因素,耦合建模可以采用一维计算中推荐的密封泄漏系数值。      

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

基于IPSO-Elman神经网络的飞机客舱能耗预测

为了提高飞机客舱使用地面空调制冷时客舱能耗的预测精度，提出了一种改进的粒子群优化（IPSO）Elman神经网络的飞机客舱能耗预测模型。依据对算法中惯性权重与学习因子的收敛域分析，得出了二者合理的取值范围，将粒子到全局最优位置间距离与参数的取值范围相结合，构造了惯性权重与学习因子的动态调节函数，对其进行非线性的动态调节，并引入了变异因子，提出了一种跳出局部最优的策略，防止粒子群优化（PSO）陷入局部最优。将IPSO-Elman应用于Boeing738飞机客舱能耗预测中，与PSO-Elman、Elman算法进行性能比较，仿真结果表明基于IPSO-Elman的客舱能耗预测模型在预测精度和收敛速度方面均有一定的提升。该研究结果为飞机客舱能耗预测模型的建立提供了理论依据，对飞机地面空调的节能与机场电能合理调配提供了支持。     

谐振式加速度计自激振荡电路性能评价方法的研究

针对谐振式加速度计成品率不高、精度低等问题，以石英振梁加速度计为例，采用引进标准信号，将谐振电路作为“黑盒子”，对其开展独立的评价。通过评价电路的驱动电压幅值稳定性、移相稳定性、全温幅值/相位对称性等指标，与加速度计实际指标建立了一一对应的关系，为加速度计研制与性能提升提供了有效依据。实际运用表明，电路噪声性能、温度性能大幅提升，产品成品率从70%提高到了约90%。     

Orbital stability close to asteroid 624 Hektor using the polyhedral model

We investigate the orbital stability close to the unique L4-point Jupiter binary Trojan asteroid 624 Hektor. The gravitational potential of 624 Hektor is calculated using the polyhedron model with observational data of 2038 faces and 1021 vertexes. Previous studies have presented three different density values for 624 Hektor. The equilibrium points in the gravitational potential of 624 Hektor with different density values have been studied in detail. There are five equilibrium points in the gravitational potential of 624 Hektor no matter the density value. The positions, Jacobian, eigenvalues, topological cases, stability, as well as the Hessian matrix of the equilibrium points are investigated. For the three different density values the number, topological cases, and the stability of the equilibrium points with different density values are the same. However, the positions of the equilibrium points vary with the density value of the asteroid 624 Hektor. The outer equilibrium points move away from the asteroid’s mass center when the density increases, and the inner equilibrium point moves close to the asteroid’s mass center when the density increases. There exist unstable periodic orbits near the surface of 624 Hektor. We calculated an orbit near the primary’s equatorial plane of this binary Trojan asteroid; the results indicate that the orbit remains stable after 28.8375?d.     

基于TLE的弹道系数计算方法及应用分析

针对仅使用两行要素（Two Line Element，TLE）作为数据源的应用需求，研究了基于TLE轨道衰减的弹道系数计算方法。介绍了一种常用的基于两组TLE的直接计算法，分析TLE选取间隔对结果精度的影响；提出了一种基于多组TLE的迭代计算方法，以降低异常TLE对计算结果的影响；从弹道系数计算效果、在再入预报中的应用等方面对这两种方法进行比较分析。结果表明，两种方法各有优劣，基于多组TLE的迭代计算法稳定性更高、受TLE精度的影响更小；由于数据区间更短，基于两组TLE的计算结果对短期轨道衰减特性反应得更准确，用于临近再入时的预报效果更好。